Vulcan-Hart ERO21 Dokumentacja

ERD/ERC SERIES ELECTRIC FRYERSMODELS MANUFACTURED AFTER AUGUST 2003WITH TDI CONTROLLERSERD50 ML-135541ERD85 ML-135543ERC50 ML-135545ERC85 ML-135547ERO

— 10 —CONTROLS —Control GuideERD SERIES(MANUFACTURED AFTER AUGUST 2003 WITH TDI CONTROLLERS)— Power switch; for turning the fryer on or off.— For clea

— 11 —PARAMETER SELECT DISPLAY SCROLLLeft TimerPress or to enter time.LED is lit above the left basketicon. The time value is displayed

— 12 —Melt Options (ERD Series)When using solid shortening in the fryer, the CY S (solid shortening) option must be used. Solidshortening must be gent

— 13 —USING THE FRYER (After Startup)Models Without Basket Lift Option1. Load the fry basket(s); do not overfill.2. Carefully lower basket(s) into sho

— 14 —Control GuideCONTROLS —ERC SERIES(MANUFACTURED AFTER AUGUST 2003 WITH TDI CONTROLLERS)— Power switch; for turning the fryer on or off.— For sett

— 15 —PARAMETER STEPS LEFT DISPLAY RIGHT DISPLAYPress SELECT OPTIONSPress DEGREES F or C F or CPress to select Fahrenheit or Celsius. DEGREES

— 16 —PARAMETER STEPS LEFT DISPLAY RIGHT DISPLAYPress SELECT OPTIONSPress ENGLISH (Factory Default) LANGUAGEPress to select a language. ENGLI

— 17 —Melt Options (GRC Series)When using solid shortening in the fryer, the SOLID melt option must be used. Solid shortening mustbe gently warmed to

— 18 —TEMPERATURE AND TIME PROGRAMMINGTemperature1. Press to enter program mode. PROGRAM is displayed in the window.2. Press to enter temperatu

— 19 —Setting Advanced Time Features1. Press and enter the program mode.2. Press for timers through , or press for timers through

— 2 —TABLE OF CONTENTSGENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

— 20 —USING THE FRYER (After Startup)Models Without Basket Lift Option1. Load the fry basket(s), do not overfill.2. Carefully lower basket(s) into sho

— 21 —FRYING (All Models)Heat shortening to set temperature.Pieces of product to be fried should be about the same size to ensure the same doneness.Dr

— 22 —DAILY FILTERINGFryers Without Filter Ready OptionsTurn power switch off when draining or filling.Always filter the shortening while liquified.

— 23 —CLEANING (All Models)WARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY TO THE MACHINEAND FOLLOW LOCKOUT/TAGOUT PROCEDURES.DailyClean the exterio

— 24 —CLEANING (CONTINUED)Weekly or as Required1. Once the shortening has been drained, flush out scraps and sediment with a small amount of warmshort

— 25 —TROUBLESHOOTINGALARMS AND ERROR MESSAGESOpen Probe - If an open probe is detected, the heat demand is disabled and any running cooking cyclesare

— 26 —MAINTENANCEWARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANINGAND SERVICING THE FRYER.WARNING: SPILLING HOT FRYING CO

— 27 —NOTES

— 28 —FORM 35611 (08-03) PRINTED IN U.S.A.NOTES

— 3 —Installation, Operation and Care ofMODEL ERD/ERC SERIES ELECTRIC FRYERSSAVE THESE INSTRUCTIONS FOR FUTURE USEGENERALVulcan ERD/ERC Series Electri

— 4 —ER Series Fryer — Construction FeaturesModel Filter ReadyBattery BatteryConfiguration InterplumbingERD50/ERC50 Opt. (Use MF50) Opt. Opt.ERD85/ERC

— 5 —ERO Series Frymate — Finish OptionsModel ERO15, ERO21 Front Door LegsStandard Stainless Steel Stainless Steel LegsOptional Not Applicable Casters

— 6 —INSTALLATIONBefore installing the fryer, verify that the electrical service agrees with the specifications on the fryerdata plate which is locate

— 7 —Fig. 1LEVELINGPlace a carpenter's level on top of the fryer and level the fryer front-to-back and side-to-side by turningthe adjustable legs

— 8 —OPERATIONWARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING,CLEANING AND SERVICING THE FRYER.WARNING: SPILLING HOT FRYING COM

— 9 —ADDING SOLID SHORTENINGIf replacing shortening, place the block of shortening in the room with the fryer for 1 to 2 hours beforeusing. This will